UK Vintage Radio Repair and Restoration Powered By Google Custom Search Vintage Radio and TV Service Data

Go Back   UK Vintage Radio Repair and Restoration Discussion Forum > Specific Vintage Equipment > Vintage Radio (domestic)

Notices

Vintage Radio (domestic) Domestic vintage radio (wireless) receivers only.

Closed Thread
 
Thread Tools
Old 16th May 2022, 7:37 pm   #1
tin0gauge
Tetrode
 
tin0gauge's Avatar
 
Join Date: Oct 2013
Location: Guildford, Surrey, UK.
Posts: 82
Default AC/ DC radios live chassis.

Hello, on an AC / DC chassis like the Marconi T18DA which has a live chassis should the neutral go to the chassis? The existing mains wire is not colour coded.
tin0gauge is offline  
Old 16th May 2022, 8:03 pm   #2
PJL
Dekatron
 
Join Date: Sep 2005
Location: Seaford, East Sussex, UK.
Posts: 5,997
Default Re: AC/ DC radios live chassis.

AC/DC sets are not very safe under any circumstance but the T18DA does have a double pole mains switch so the side that switches to the chassis should be connected to Neutral. Many of the cheap imported USA sets have a single pole switch that disconnects the connection to chassis and if you connect this to neutral then the heater chain will make the chassis LIVE when switched off (only solution is to change the switch for double pole).
PJL is offline  
Old 16th May 2022, 8:39 pm   #3
kalee20
Dekatron
 
Join Date: Feb 2007
Location: Lynton, N. Devon, UK.
Posts: 7,060
Default Re: AC/ DC radios live chassis.

Yes, the neutral should go to chassis if possible. (If you're operating it on DC and the positive happens to be grounded, you don't have a choice of course!)
kalee20 is offline  
Old 16th May 2022, 9:03 pm   #4
cathoderay57
Nonode
 
Join Date: Oct 2017
Location: Bristol, UK.
Posts: 2,364
Default Re: AC/ DC radios live chassis.

Ideally, operate it using an isolating mains transformer. Jerry
cathoderay57 is offline  
Old 16th May 2022, 9:06 pm   #5
Nickthedentist
Dekatron
 
Nickthedentist's Avatar
 
Join Date: Jan 2005
Location: Oxford, UK.
Posts: 17,820
Default Re: AC/ DC radios live chassis.

Lots of useful info here: https://www.vintage-radio.com/repair...ly-stages.html
Nickthedentist is offline  
Old 17th May 2022, 12:48 am   #6
Techman
Dekatron
 
Techman's Avatar
 
Join Date: Nov 2009
Location: Lincolnshire, UK.
Posts: 4,985
Default Re: AC/ DC radios live chassis.

Quote:
Originally Posted by cathoderay57 View Post
Ideally, operate it using an isolating mains transformer. Jerry
Absolutely, that's the ultimate answer if you're worried about safety.

As for switching, the best method is a single pole switch in the LIVE only, with the neutral permanently hard wired to chassis for best safety.
Techman is offline  
Old 17th May 2022, 10:19 am   #7
Nickthedentist
Dekatron
 
Nickthedentist's Avatar
 
Join Date: Jan 2005
Location: Oxford, UK.
Posts: 17,820
Default Re: AC/ DC radios live chassis.

Quote:
Originally Posted by Techman View Post
As for switching, the best method is a single pole switch in the LIVE only, with the neutral permanently hard wired to chassis for best safety.
Or simply switch off by pulling out the mains plug, which also saves wear and tear on the radio's mains switch and volume/tone pot if they're combined with it.
Nickthedentist is offline  
Old 17th May 2022, 10:39 am   #8
ms660
Dekatron
 
ms660's Avatar
 
Join Date: Apr 2011
Location: Cornwall, UK.
Posts: 13,454
Default Re: AC/ DC radios live chassis.

With the mains Neutral connected to/switched through to chassis a Neutral interrupt could surprise the unwary

Lawrence.
ms660 is offline  
Old 17th May 2022, 11:10 am   #9
G6Tanuki
Dekatron
 
G6Tanuki's Avatar
 
Join Date: Apr 2012
Location: Wiltshire, UK.
Posts: 13,951
Default Re: AC/ DC radios live chassis.

It was somewhat normal for the switch to be in the neutral wire though, because this means that when the radio is switched on the power wiring adjacent to the volume control wiring is at chassis potential, meaning less chance of AC hum getting across and into the audio circuit.
Putting the switch in the live wire means you have 250Volts passing rather close to the volume control..
__________________
I'm the Operator of my Pocket Calculator. -Kraftwerk.
G6Tanuki is offline  
Old 17th May 2022, 11:21 am   #10
Nickthedentist
Dekatron
 
Nickthedentist's Avatar
 
Join Date: Jan 2005
Location: Oxford, UK.
Posts: 17,820
Default Re: AC/ DC radios live chassis.

Yes, I have several AC/DC sets where the switch is single-pole and in the neutral/chassis connection, e.g. Roberts P5A.
Nickthedentist is offline  
Old 17th May 2022, 1:27 pm   #11
emeritus
Dekatron
 
Join Date: Jan 2012
Location: Brentwood, Essex, UK.
Posts: 5,316
Default Re: AC/ DC radios live chassis.

In the days when 2 pin plugs, or a BC adaptor in a light socket, were commonly used to power domestic appliances, it was a 50:50 chance which conductor would be "hot".
emeritus is offline  
Old 17th May 2022, 5:24 pm   #12
usradcoll1
Heptode
 
Join Date: Mar 2017
Location: Cedar Grove, Wisconsin, USA.
Posts: 823
Default Re: AC/ DC radios live chassis.

Quote:
Originally Posted by PJL View Post
AC/DC sets are not very safe under any circumstance but the T18DA does have a double pole mains switch so the side that switches to the chassis should be connected to Neutral. Many of the cheap imported USA sets have a single pole switch that disconnects the connection to chassis and if you connect this to neutral then the heater chain will make the chassis LIVE when switched off (only solution is to change the switch for double pole).
In the US, we're a little casual in our design of electrical products because of our low mains voltage.
Most of the radios exported to 220/240 volt countries, generally were the inexpensive makes using a resistive mains lead, which isn't very impressive.
Our listing agencies, such as U/L would not approve this design.
Dave, USradcoll1.
usradcoll1 is offline  
Old 17th May 2022, 5:59 pm   #13
winston_1
Hexode
 
Join Date: Oct 2012
Location: London, UK.
Posts: 497
Default Re: AC/ DC radios live chassis.

With radios with a line cord (resistive dropper in the lead) the switch has to go in the neutral.
winston_1 is offline  
Old 18th May 2022, 9:53 am   #14
lesmw0sec
Octode
 
Join Date: Jul 2009
Location: Carmel, Llannerchymedd, Anglesey, UK.
Posts: 1,498
Default Re: AC/ DC radios live chassis.

Quote:
Originally Posted by emeritus View Post
In the days when 2 pin plugs, or a BC adaptor in a light socket, were commonly used to power domestic appliances, it was a 50:50 chance which conductor would be "hot".
Indeed. In my apprentice days, i was advised to see if the chassis was live by gently drawing the back of the hand across it and detecting a 'buzz'!
lesmw0sec is offline  
Old 18th May 2022, 11:38 am   #15
Herald1360
Dekatron
 
Herald1360's Avatar
 
Join Date: Feb 2007
Location: Leominster, Herefordshire, UK.
Posts: 16,527
Default Re: AC/ DC radios live chassis.

Quote:
Originally Posted by winston_1 View Post
With radios with a line cord (resistive dropper in the lead) the switch has to go in the neutral.
Why?

Most line cords were simply a resistor in series with the whole set, at any rate for US imports. The position of a switch in a simple series circuit has no effect on its switching function.

There were some UK designs with tapped line cords which allowed higher HT voltage to which this could apply I guess though a single switch in the heater feed branch would still work and would have the advantage of leaving the chassis at neutral with fewer parts still live than with switched neutral. And no worse off than any other AC/DC with reversed mains in and single pole switching either.
__________________
....__________
....|____||__|__\_____
.=.| _---\__|__|_---_|.
.........O..Chris....O
Herald1360 is offline  
Old 18th May 2022, 5:31 pm   #16
usradcoll1
Heptode
 
Join Date: Mar 2017
Location: Cedar Grove, Wisconsin, USA.
Posts: 823
Default Re: AC/ DC radios live chassis.

Quote:
Originally Posted by Herald1360 View Post
Quote:
Originally Posted by winston_1 View Post
With radios with a line cord (resistive dropper in the lead) the switch has to go in the neutral.
Why?

Most line cords were simply a resistor in series with the whole set, at any rate for US imports. The position of a switch in a simple series circuit has no effect on its switching function.

There were some UK designs with tapped line cords which allowed higher HT voltage to which this could apply I guess though a single switch in the heater feed branch would still work and would have the advantage of leaving the chassis at neutral with fewer parts still live than with switched neutral. And no worse off than any other AC/DC with reversed mains in and single pole switching either.
Some of the US makes used to offer an extension lead that contained a resistor for that particular model, intended for export to area with higher voltage mains.
Dave, USradcoll1
usradcoll1 is offline  
Old 18th May 2022, 6:05 pm   #17
broadgage
Nonode
 
Join Date: Jan 2010
Location: North Somerset, UK.
Posts: 2,129
Default Re: AC/ DC radios live chassis.

Yes, the neutral side of the AC mains should go to chassis.
With DC mains, the user got no choice, and with non polarised plugs on AC it was pot luck.

But these days with DC mains being effectively extinct, and polarised plugs being almost universal, then neutral to chassis.

For best safety turn the set off at the socket outlet when not being used.
broadgage is offline  
Old 18th May 2022, 8:52 pm   #18
Sideband
Dekatron
 
Sideband's Avatar
 
Join Date: Oct 2003
Location: Croydon, Surrey, UK.
Posts: 7,548
Default Re: AC/ DC radios live chassis.

Quote:
Originally Posted by PJL View Post
AC/DC sets are not very safe under any circumstance
They can't be that unsafe! TV's used the same technology for a lot longer and I repaired hundreds of them without the hint of any danger. The workshop I started in didn't have isolation transformers and the benches were fitted with two-pin plugs so worked on the sets (radio's and TV's) on raw mains. All I did was check the chassis with a neon screwdriver to see if it was live or not.

An isolation transformer doesn't really make the sets safer. You can still get a nasty belt if you touch anything live. All the transformer does is enable you to connect earthed test equipment.
__________________
There are lots of brilliant keyboard players and then there is Rick Wakeman.....
Sideband is online now  
Old 19th May 2022, 9:53 am   #19
ms660
Dekatron
 
ms660's Avatar
 
Join Date: Apr 2011
Location: Cornwall, UK.
Posts: 13,454
Default Re: AC/ DC radios live chassis.

Re: Isolating transformer, see Post#8.

Lawrence.
ms660 is offline  
Old 19th May 2022, 10:03 am   #20
Hybrid tellies
Nonode
 
Hybrid tellies's Avatar
 
Join Date: Jan 2004
Location: 1966-1976 Coverack in Cornwall and Helston Cornwall. 1976-present Bristol/Bath area.
Posts: 2,965
Default Re: AC/ DC radios live chassis.

Quote:
Originally Posted by Sideband View Post
Quote:
Originally Posted by PJL View Post
AC/DC sets are not very safe under any circumstance
They can't be that unsafe! TV's used the same technology for a lot longer and I repaired hundreds of them without the hint of any danger. The workshop I started in didn't have isolation transformers and the benches were fitted with two-pin plugs so worked on the sets (radio's and TV's) on raw mains. All I did was check the chassis with a neon screwdriver to see if it was live or not.

An isolation transformer doesn't really make the sets safer. You can still get a nasty belt if you touch anything live. All the transformer does is enable you to connect earthed test equipment.
Totally agree. My first few years after leaving school being employed as a trannie TV engineer all the television sets we worked on were AC/DC and there was no isolation transformer in the workshop or in customers houses. It was down to the good training we received from other engineers and of course the college that kept us and our customers safe.
__________________
Simon
BVWS member
Hybrid tellies is offline  
Closed Thread

Thread Tools



All times are GMT +1. The time now is 8:27 pm.


All information and advice on this forum is subject to the WARNING AND DISCLAIMER located at https://www.vintage-radio.net/rules.html.
Failure to heed this warning may result in death or serious injury to yourself and/or others.


Powered by vBulletin®
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
Copyright ©2002 - 2023, Paul Stenning.