UK Vintage Radio Repair and Restoration Powered By Google Custom Search Vintage Radio and TV Service Data

Go Back   UK Vintage Radio Repair and Restoration Discussion Forum > General Vintage Technology > Hints, Tips and Solutions (Do NOT post requests for help here)

Notices

Hints, Tips and Solutions (Do NOT post requests for help here) If you have any useful general hints and tips for vintage technology repair and restoration, please share them here. PLEASE DO NOT POST REQUESTS FOR HELP HERE!

Closed Thread
 
Thread Tools
Old 14th Feb 2003, 7:54 pm   #1
rmorti
Pentode
 
Join Date: Dec 2002
Location: Winchester, Hampshire, UK.
Posts: 103
Default Stripped Threads in Bakelite

Hi

A quick one out of recent experience with a DAC90A...a definate design shortcoming (daresay in other sets also) is the tapping of threads for bolts directly into the bakelite, instead of moulding in a brass threaded insert. Relies on thick bushes and a fair length of thread to prevent the thread stripping, but...these things happen (one of the speaker mounting points on my set)!

An almost ideal fix is to use a short length of plastic cable tie, trimmed to a suitable size and thickness, inserted into the stripped hole to give the screw something to bite on. Has to be trimmed so as not to unduly stress the mounting bush as the screw's done up, of course, but the squashy plastic/nylon used provides just the right amount of grip.

Richard
rmorti is offline  
Old 6th Mar 2003, 4:18 pm   #2
rob
Guest
 
Posts: n/a
Default Re: Stripped Threads in Bakelite

PTFE tape also works. It is used by plumbers for sealing pipe threads and can be obtained from B&Q, Wickes, etc.

Last edited by Paul Stenning; 26th Dec 2004 at 11:53 pm. Reason: Fix link or code for vBulletin
 
Old 6th Dec 2003, 9:37 pm   #3
JHGibson
Retired Dormant Member
 
Join Date: Apr 2003
Location: Salt Spring Island, BC, Canada
Posts: 368
Default Re: Stripped Threads in Bakelite

When faced with this problem in the past, I just retapped the hole to the next larger standard screw thread. You will need to finish the threadcutting with a blind hole type tap after the first cut with a standard tap. In either case do not force the tap with higher torque than that you began tapping with, otherwise you might have bottomed the tap in the meantime and the increased forces could split the bakelite and create an even bigger problem! This is one repair job where experience really counts. I recomend you drill blind holes in a piece of scrap bakelite and practise first.
If you do not want to use a larger screw, you could fill the stripped hole with Araldite epoxy and after it sets then use a appropriate drill and tap to the original size.
One repair method that I plan to try on my next stripped thread is to fill the hole half full with Araldite with the entire hole wall wet with it and then run the original screw fully in and then let the epoxy set. The screw will need a faint hint of oil on it to act as a release agent so the the screw is not permanently glued in! This is only a thought and is totally untried. Did anyone try this already?
JHGibson is offline  
Old 6th Dec 2003, 10:29 pm   #4
Tim
Dekatron
 
Tim's Avatar
 
Join Date: Jan 2003
Location: Bradford on Avon, Wiltshire, UK.
Posts: 3,301
Default Re: Stripped Threads in Bakelite

Car filler works very well too, and like Araldite can also be drilled and tapped. It may be coloured/painted afterwards if required.
Regards
Tim
__________________
"Nothing is as dangerous as being too modern;one is apt to grow old fashioned quite suddenly."
Tim is offline  
Closed Thread

Thread Tools



All times are GMT +1. The time now is 7:36 pm.


All information and advice on this forum is subject to the WARNING AND DISCLAIMER located at https://www.vintage-radio.net/rules.html.
Failure to heed this warning may result in death or serious injury to yourself and/or others.


Powered by vBulletin®
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
Copyright ©2002 - 2023, Paul Stenning.