UK Vintage Radio Repair and Restoration Powered By Google Custom Search Vintage Radio and TV Service Data

Go Back   UK Vintage Radio Repair and Restoration Discussion Forum > Specific Vintage Equipment > Vintage Telephony and Telecomms

Notices

Vintage Telephony and Telecomms Vintage Telephones, Telephony and Telecomms Equipment

Closed Thread
 
Thread Tools
Old 23rd Apr 2020, 7:28 pm   #1
Dave Moll
Dekatron
 
Dave Moll's Avatar
 
Join Date: Feb 2005
Location: West Cumbria (CA13), UK
Posts: 6,118
Default Bellset 44 problem with indicator

The indicator for the extension being in use on my bellset 44 has a problem in that it is not clearing after it has been set. There is nothing mechanically preventing it from returning, as moving it to the "set" position by hand allows it to return without problem. It seems more that the solenoid is remaining magnetised until its armature is manually released.

I do notice that a switch (marked "I1"?) on the diagram places a 2μF capacitor across the coil, but I'm struggling to identify what that switch is.

Any thoughts on the cause of the problem?
__________________
Mending is better than Ending (cf Brave New World by Aldous Huxley)
Dave Moll is online now  
Old 23rd Apr 2020, 8:47 pm   #2
OscarFoxtrot
Heptode
 
OscarFoxtrot's Avatar
 
Join Date: Apr 2011
Location: Edinburgh, UK.
Posts: 805
Default Re: Bellset 44 problem with indicator

I'd guess it's contact 1 on relay I - which is the Indicator, which is labelled I over 1, suggesting it's a relay with one contact set.
OscarFoxtrot is offline  
Old 23rd Apr 2020, 9:32 pm   #3
Dave Moll
Dekatron
 
Dave Moll's Avatar
 
Join Date: Feb 2005
Location: West Cumbria (CA13), UK
Posts: 6,118
Default Re: Bellset 44 problem with indicator

The indicator is indeed a relay with one contact set, and the capacitor is shown as across the coil when the relay is operated, so could this be what is keeping the coil energised after the extension breaks the loop? It doesn't appear, however, that shorting out the coil releases the relay.
__________________
Mending is better than Ending (cf Brave New World by Aldous Huxley)
Dave Moll is online now  
Old 24th Apr 2020, 10:13 am   #4
Herald1360
Dekatron
 
Herald1360's Avatar
 
Join Date: Feb 2007
Location: Leominster, Herefordshire, UK.
Posts: 16,526
Default Re: Bellset 44 problem with indicator

Maybe a paper shim on the end of the magnetic core would "fix" the problem?
__________________
....__________
....|____||__|__\_____
.=.| _---\__|__|_---_|.
.........O..Chris....O
Herald1360 is offline  
Old 24th Apr 2020, 10:40 am   #5
Station X
Moderator
 
Station X's Avatar
 
Join Date: Jan 2003
Location: Ipswich, Suffolk, IP4, UK.
Posts: 21,192
Default Re: Bellset 44 problem with indicator

A capacitor across a relay coil is normally used to provide a slow release function.

Many telephone relays had a residual stud, of non-magnetic material, between the pole face and the armature to break the magnetic path and prevent the armature being held in by residual magnetism. Tape as suggested by Herald1360 will also do the job.
__________________
Graham. Forum Moderator

Reach for your meter before you reach for your soldering iron.
Station X is online now  
Old 24th Apr 2020, 11:50 am   #6
Dave Moll
Dekatron
 
Dave Moll's Avatar
 
Join Date: Feb 2005
Location: West Cumbria (CA13), UK
Posts: 6,118
Default Re: Bellset 44 problem with indicator

I think the capacitor (or any other electrical energising) was innocent, given that the relay had failed to release over twelve hours later.

Thank you, Chris, for the shim idea. That was successful, so presumably it was residual magnetism. The end of the core now has a small round sticky label attached to it serving the same function.

Maybe there would originally have been some such barrier that has subsequently fallen off and gone missing.
__________________
Mending is better than Ending (cf Brave New World by Aldous Huxley)
Dave Moll is online now  
Old 24th Apr 2020, 2:08 pm   #7
Herald1360
Dekatron
 
Herald1360's Avatar
 
Join Date: Feb 2007
Location: Leominster, Herefordshire, UK.
Posts: 16,526
Default Re: Bellset 44 problem with indicator

"Residual stud".

I knew there would be a proper term for it....
__________________
....__________
....|____||__|__\_____
.=.| _---\__|__|_---_|.
.........O..Chris....O
Herald1360 is offline  
Old 24th Apr 2020, 2:29 pm   #8
Station X
Moderator
 
Station X's Avatar
 
Join Date: Jan 2003
Location: Ipswich, Suffolk, IP4, UK.
Posts: 21,192
Default Re: Bellset 44 problem with indicator

Sometimes took the form of a screw with a locknut. A special feeler gauge with a hole in it was positioned between the armature and pole face with the screw thread passing through the hole. The screw was then adjusted until the gauge was just gripped.
__________________
Graham. Forum Moderator

Reach for your meter before you reach for your soldering iron.
Station X is online now  
Old 24th Apr 2020, 3:35 pm   #9
Dave Moll
Dekatron
 
Dave Moll's Avatar
 
Join Date: Feb 2005
Location: West Cumbria (CA13), UK
Posts: 6,118
Default Re: Bellset 44 problem with indicator

Yes, there is. I'll leave the temporary fix for the moment - until I find a suitable spanner to loosen the locknut, as there's not a lot of room - but thanks pointing out how the adjustment should be made.
__________________
Mending is better than Ending (cf Brave New World by Aldous Huxley)
Dave Moll is online now  
Old 15th May 2020, 12:29 pm   #10
Dave Moll
Dekatron
 
Dave Moll's Avatar
 
Join Date: Feb 2005
Location: West Cumbria (CA13), UK
Posts: 6,118
Default Re: Bellset 44 problem with indicator

As a slightly off-topic addendum to this, I have now finished incorporating this bellset 44 into a plan 5 with two internal extensions - the finishing touch having been applied when (with a stroke of serendipity) I managed to acquire the three bells 56 needed for internal signalling between the main and the extensions.
__________________
Mending is better than Ending (cf Brave New World by Aldous Huxley)
Dave Moll is online now  
Old 16th May 2020, 11:49 am   #11
davidw
Heptode
 
davidw's Avatar
 
Join Date: Sep 2006
Location: Woodbridge, Suffolk, UK.
Posts: 641
Default Re: Bellset 44 problem with indicator

Residual studs were part of relay adjustment in the day.
Gauges had a hole in to allow the bolt type to be adjusted or to check the wear on fixed studs.
This set was on my first van when I got it in '69 it dates from 1957
Attached Thumbnails
Click image for larger version

Name:	IMG_1454.jpg
Views:	63
Size:	41.2 KB
ID:	205971   Click image for larger version

Name:	IMG_1452.jpg
Views:	58
Size:	52.8 KB
ID:	205972  
__________________
Dave G1AGK.
My perception is my reality!
davidw is offline  
Closed Thread

Thread Tools



All times are GMT +1. The time now is 11:21 am.


All information and advice on this forum is subject to the WARNING AND DISCLAIMER located at https://www.vintage-radio.net/rules.html.
Failure to heed this warning may result in death or serious injury to yourself and/or others.


Powered by vBulletin®
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
Copyright ©2002 - 2023, Paul Stenning.